產品詳情
一、焊接過程:
1. Welding process:
1. 焊接規范見《焊接工藝》（YTRS643-91-01A），除以下特殊要求外 ，其他焊接要求均按照《焊接技術要求》（YTRS643-91-02）執行。
For the 1. welding specification, see "welding process" (YTRS643-91-01A), except for the following special requirements, the other welding requirements are carried out according to the welding technical requirements (YTRS643-91-02).
2. 保護金屬表面，嚴禁隨處引弧，任意用鐵錘敲擊金屬表面。
2. protect the bl surface. It is forbidden to strike the arc anywhere, and hammer the bl surface with any hammer.
3. 與不銹鋼焊接的臨時性構件（如馬板、吊耳等），要使用相同的不銹鋼材料，采用相應的焊接工藝。
3. temporary components welded with stainless steel, such as horse boards and lifting lugs, shall be made of the same stainless steel and corresponding welding process.
4.焊接不銹鋼鋼管時，管內應通惰性氣體進行凈化，焊接時焊縫附近區域必須持續有氬氣保護。
4. when welding stainless steel pipe, the pipe should be cleaned by inert gas. Argon must be protected after welding.
5.焊接不銹鋼鋼管時，需用TIG焊打底。
5. welding stainless steel pipe, the need to use TIG welding bottom.
6. 使用不銹鋼材質的砂輪和鋼絲刷等進行打磨和清理工作。
6. grinding and cleaning with stainless steel wheels and wire brushes.
二、 焊后處理:
Two. Post welding:
1. 焊后應對焊縫及近縫區做酸洗、鈍化處理。
After 1. welding, pickling and passivation should be done to weld and near seam area.
2. 酸洗、鈍化步驟如下:
2. the steps of pickling and passivation are as follows:
2.1 將焊縫表面清理干凈。
2.1 clean the surface of the weld.
2.2 再將酸洗、鈍化膏涂抹于焊縫及近縫區具有氧化皮處，涂膜厚度為1~3mm。
2.2 then apply acid pickling and passivation paste to the weld and near seam area with oxide scale, and the film thickness is 1~3mm.
2.3 反應一般為1-10分鐘，0℃以下，氧化皮厚處，需適當延長時（反應時間視膏體品牌及金屬氧化膜厚度而定）。
The 2.3 reb is generally 1-10 minutes, below 0 degrees, and the thickness of oxidized skin should be extended appropriaby (reb time depends on the brand of the paste and the thickness of the bl oxide film).
2.4待反應完全后，用抹布或絲刷擦除，清水沖凈即可。
2.4 after the reb is complete, wipe with a cloth or silk brush and rinse with clean water.
泰安揚帆數控科技有限公司將秉承“以質量求生存，以管理求效益，以科技求發展”的文化理念，繼往開來，努力拼搏，奮發向上，創造民族自動化焊接世界品牌！
泰安揚帆數控科技有限公司
諾商基于多年的優化經驗和品牌基礎推出的諾商商道系統，諾商信息您身邊的互聯網專家！
