產品詳情
雙吸循環泵@平鄉縣雙吸循環泵@雙吸循環泵300口徑
Bushing comb, shaft parts using flat keys and round nuts fixed, locking, so that it becomes one, the entire rotor by the two ends of the bearing support. The impeller of the medium open pump transmits the energy of the original motive through the b of centrifugal force to the liquid in the pump, which increases the speed and pressure of the liquid, causes the liquid in the pump to drain out, and the liquid in the inlet pipe is sucked in. The medium open pump impeller is installed in the pump shell and fastened to the pump shaft, and the pump shaft is directly driven by the motor. The pump shell has a liquid connected to the tube. The liquid enters the pump through the bottom valve and tube. The liquid outlet on the pump shell is connected with the discharge pipe. When the speed of the pump is certain, its pressure head, the flow rate is related to the impeller diameter. The shape of the impeller blade of the middle open pump lies in the accord with the flow law. The motion law of liquid in impeller should be studied first. In order to study the flow law of liquid in the impeller, we take the liquid flow in the impeller from the front cover to the back cover to the hard layer, each layer of phase b on a flow surface. The liquid flows only along each layer, and the liquid of the layer and layer does not mix with each other.
運行數據：出口直徑：DN=80～800mm流量：50～11600m3/h(額定點)揚程：H＝7.6～200m(額定點)許用工作壓力：≤2.5MPa許用試驗壓力：≤3.75MPa介質：清水或物理化學性質類似于清水的其它液體(固體顆?！?0mg/L)。溫度：≤105°C水力經優化設計三水力模型，不僅使泵具有優異的水力性能，并且沒有軸向力(理論上)這一困擾水泵特別是大型水泵運行的難題。泵體、泵蓋、葉輪經精密鑄造，過流表面光滑提高了泵的抗汽蝕性能和效率。密封根據輸送介質或用戶要求采用填料密封或機械密封，不受轉向限制。對于填料密封，有足夠的空間用于更換填料。jdhuiquan4.13
雙吸循環泵@平鄉縣雙吸循環泵@雙吸循環泵300口徑
If you spray oil outward, you should stop and check immediaby. The purchase of mechanical seals at different prices has a significant impact on their quality. Take quality control measures mechanical seal before leaving the factory must do sealing perbance test, and have a certificate. Mechanical seal after long-term operation, so that the dynamic ring and static ring wear, spring and shaft rust wear, sealant ring wear, aging, debation, etc., can cause sealing leakage, must repair or replace new parts. The sealing surface of the dynamic ring and static ring shall not have cracks, corners, scratches, hemp points, flying edges and partial grinding, scratches, hemp points can not run through the entire sealing end surface. If the fixed static and dynamic ring is used, the height of the convex of the static and dynamic ring is not less than 3mm, and the height of a single convex is not less than lmm, so as not to affect the heat dissipation. 3 Dynamic ring After installation should be guaranteed to move flexibly on the shaft, the dynamic ring pressure on the spring should be able to bounce back freely, to maintain the vertical and parallel of the static and dynamic ring. Reasonable selection of medium-open pump, is to consider the pump unit and pumping station investment and operating costs, such as comprehensive technical and economic indicators.
產品概述：S、SA系列雙吸中開泵，主要供輸送溫度不高于105°C的清水或理化性質類似于水的液體。適用于自來水廠、泵站、電站、空調循環用水、采暖用熱水循環、工業供水系統、消防系統、船舶、煉油工業(一般性液體)等輸送液體的場合。
產品特點：
1、內置式密封潤滑結構：泵內置式密封潤滑結構，密封循環水對泵密封系統的潤滑、沖洗更為直接、有效。
2、外形美觀：直線型的外觀并在泵蓋上附加強筋，內置式密封潤滑結構使泵整體結構渾然一體，靈活的結構設計使泵更加精美大方。
3、率：采用CFD計算流體動力學，分析計算出泵內壓力分布和速度分布關系、優化泵的流道設計，確保泵有的水力形線，提高了泵的效率。泵體采用雙流道設計，以減小徑向力。泵體、泵蓋、葉輪等過流部采用樹脂砂板模造型，保證了外觀及流道尺寸以及泵的水力效率。S、SA系列雙吸中開泵效率比一般雙吸泵高3～5％。
4、平衡精度高：轉子部件動平衡精度為G1。0級。
5、軸：軸短且剛性好，增加軸徑，以延長軸承和機械密封的使用壽命。軸為全封結構，確保了不與介質接觸，不銹蝕，使用壽命長。
6、雙蝸殼：高揚程泵采用雙蝸殼結構，減輕了徑向力。
雙吸循環泵@平鄉縣雙吸循環泵@雙吸循環泵300口徑
裝配完成后，用手轉動泵軸，沒有擦碰現象，轉動比較輕滑均勻即可，拆卸可按上述裝配順序相反地進行。S系列中開泵安裝1，檢査水泵和電動機應無損壞。水泵的安裝高度，加上管路的水力損失，及其速度能，不得大于樣本規定的允許吸上真空高度值?；A尺寸應符合泵機組的安裝尺寸。安裝順序：①將水泵放在埋有地腳螺栓的混凝土基礎上，用調整其間的楔型墊塊的方法校正水平，并適當擰緊地腳螺栓，以防走動。②在基礎與泵底腳之后灌注混凝土。③待混凝土干固后，擰緊地腳螺栓，并重新檢査水泵的水平度。④校正電動機軸與水泵軸的同心度。使兩軸成一直線，在兩軸器外圓上的同軸度允差為0.1mm，端面間隙沿圓周的不均勻度允差0.3mm（在聯接進出水管路及試運行后再分別校核一遍。
工作條件：
1．許用工作壓力為2.5MPa；即泵入口壓力+泵揚程≤2.5MPa。根據泵殼承受的壓力，泵體和泵蓋材質采用灰口鑄鐵(1.6MPa)、球墨鑄鐵(2.0MPa)、鑄鋼(2.5MPa)。在訂貨時敬請注明泵的承壓情況或材質。
2．介質：溫度≤105°C的清水或物理化學性質類似清水的其它液體(固體顆?！?0mg/L)。 軸承1、采用油脂潤滑的封閉式滾動軸承，維護簡單，運行時間長；2、配備恒定油位的油杯，也可用稀油潤滑；
3、選用進口(SKF、NSK、NTN)高質量軸承，運行平穩，噪音低，使用壽命長。 結構 結構緊湊、穩定性好。
S、SA系列雙吸中開泵為泵殼中開結構，進出口均在泵體上，檢修時只需吊出泵蓋，轉子部件便可移出進行檢修作業，而不需拆卸管路，十分方便。 根據需要電動機(驅動機)可以在左端也可在右端，方便現場安裝。結構上縮短轉子部件軸向尺寸，軸的鋼性更好，運行更穩定可靠。設有泵體密封環，而葉輪密封環為可選用件。密封環磨損后可以更換，減少了運行維護費用。
五、型號意義：
例如：300S58A
300-泵入口直徑(mm)
S-單級雙吸水平中開式離心清水泵
58-設計點揚程(m)
A-葉輪外徑改變標志
離心泵，自吸泵，蝶閥等。公司自興辦以來，一向專心于產品立異與開發，為了跋涉產品的層次，完善產品的售后效能，咱們時刻與客戶堅持嚴密的聯絡
在特殊的情況下，對我們目前不能自己生產，而科研上又有實際需要的儀器的進口采取一些稅收上的優惠政策是合理的，一步一個鏗鏘腳印，給這風云變幻的時代刻下了屬于我們的印記。開展各類絲網知識培訓56期、企業培訓67期、信息技術和電子商務推介會28期，共計培訓達3萬多人次。進行性科學普查，獲取海洋大數據、深海生物、微生物資源樣本，建立深淵生物DNA數據庫，帶動一系列深淵生命科學研究的開展，接下來工業和信息化部信息化和業司安筱鵬副司長解讀了今年5月份頒發的深化業與互聯網融合發展的指導意見，
