產品詳情
幫我篩選一下液下渣漿泵葉輪A遷西液下渣漿泵葉輪
一般來說,即使順式含量最高的聚合物在這一溫度下也會結晶.順丁這種低溫下所具有的較高彈性及抗硬化性能,使其與天然橡膠或丁苯橡膠并用肘,能改善它們的低溫性能.滯后損失和生熱小 由于高順式丁二烯橡膠分子鏈段的運動所需要克服周?chē)肿渔湹淖枇妥饔昧π?內摩擦小,當作用于分子的外力去掉后,順丁橡膠接頭分子能較快的回復至原狀,因此滯后損失小,生熱小。
一、產品概述SP液下渣漿泵為立式離心液下渣漿泵，浸入液下，用于輸送磨蝕性、粗顆粒、高濃度渣漿。不需要任何軸封和軸封水，在吸入量不足的工況下也能正常工作。
SP型液下渣漿泵過流部件由耐磨金屬制成。
根據渣漿池液面的高低，可選擇不同長度的泵傳動軸或吸入管。
采用多種速度和多種變型方式，使得泵在最佳工況下運行，使用壽命長，運行效益高，能滿足多類惡劣的輸送條件。
Second, SP liquid slurry pump application Range
Slurry pump is mainly suitable for conveying corrosive, coarse particles, high concentration slag slurry. Widely used in bllurgy, mining, coal, electricity, building materials, environmental protection and other departments.
Third, SP liquid slag slurry pump structure debion
The difference between the slurry pump structure of SPR liquid and the slurry pump under SP liquid is only that the parts of the dipping slag slurry are lined with corrosion-resistant rubber, the parts lined with rubber include shafts, pumps, impellers, protective plates and filters, and the connecting bolts in the lower part of the immersion liquid are equipped with rubber protective sleeves, and the transmission parts and SP pumps
SP Liquid slurry pump pump body, impeller guard plate are made of wear-resistant materials. The pump end of the bearing body adopts a double row tapered roller bearing, and the driving end adopts a single row cylindrical roller bearing, which can withstand the maximum axial load of the pump. The bearing body is fitted with a motor seat or motor bracket, which can be driven by a direct or triangle belt drive. The pump should be immersed in the slurry pool to work, the pump body suction inlet with a filter, can prevent large particles into the human pump. Jdhuiquan5.15
Four, the depth of the liquid can be extended pump self-belt liquid depth of about 70cm, according to customer requirements to increase the depth of the liquid, (the price with the addition of a long number of meters and different) please customers and customer service personnel in advance to explain.
幫我篩選一下液下渣漿泵葉輪A遷西液下渣漿泵葉輪
4，拆下中部支架，拉下聯軸器。5，拆下軸承體上下軸承蓋，即可檢討軸承狀況。二，液下泵的起動，泊車和工作需要1，液下泵電機在未設備前，應接通電源檢討改變偏向，必需與泵的規矩改變偏向一致2，液下泵裝上電機，渣漿泵報價盤動聯軸器，檢討泵軸與電機能否同心，改變能否輕重不勻，正常后再工作。
五、型號意義
40 PV-SP
40----------吐出口徑40mm
PV--------- PV型軸承組件
SP----------液下泵
水泵安裝
泵安裝的好壞對泵的運行和壽命冇重要影響，所以安裝和校正必須仔細進行。泵的外形及安裝尺寸。
